Jinma 222 electrical problem |

This topic has 10 replies, 7 voices, and was last updated 13 years, 6 months ago by Bob Rooks.

Viewing 10 reply threads

Author

Posts
- May 12, 2011 at 9:28 am #30297
  gerlamb
  Participant
  - Offline
  Hi everyone,
  
  I haven't been here in quite a while. Everything was going fine after i put in a new solenoid. Now I have a new problem. The day before yesterday, I used the tractor with no problems. Yesterday I tried to start it and it cranked strong, but I stopped cranking to give it more gas. I don't use the foot pedal, I use the hand throttle. When I tried to start it again, I heard a snap and everything went dead. None of the gages worked when I turned the key on except the gas gauge. When I tried the light buttons, the gas guage needle jumped up and down. I thought it might be a blown fuse, so I checked them and they were OK. I disconnected the battery and charged it. I also cleaned the battery terminals. When I replaced the battery, the guages and lights and horn all worked, but when I tried to start it I heard a snap again and everything when totally dead again. If anyone has any suggestions I would appreciate it.
  
  Thanks
  
  Gerry
- May 12, 2011 at 10:05 am #32285
  Affordable
  Participant
  - Offline
  Sounds like you have a loose or bad ground, follow your ground cable from the battery to where it attachs to the tractor, I think you will find your problem
  
  Tommy
  
  Affordable Tractor Sales Co.
  
  ” Your Jinma Parts Superstore”
  
  http://www.affordabletractorsalesco.com
- May 12, 2011 at 10:10 am #32286
  gerlamb
  Participant
  - Offline
  I already disconnected the cables and cleaned them and reattached them. Didn't notice any problem.
- May 12, 2011 at 12:12 pm #32289
  Ranch Hand
  Participant
  - Offline
  You may have had a 30 amp fuse blow/pop. If so, could be related to the key switch.
  
  Ronald
  
  Ranch Hand Supply
- May 12, 2011 at 12:52 pm #32290
  biggerten
  Participant
  - Offline
  Did you hear a 'click' or a 'snap'?
  
  I'm guessing you're hearing the relay/solenoid, but the starter is refusing to turn.
  
  Can you turn the engine over by jumping the terminals with a screwdriver? Careful! Make sure the tractor is out of gear before trying this!
  
  Maybe the starter just needs a good cleaning or brushes.
- May 12, 2011 at 4:28 pm #32295
  gerlamb
  Participant
  - Offline
  Thanks everyone for your suggestions. I check the ground cable as someone suggested and it was loose and rusty. I am going to replace it see what happens. When I tightened it I could start with the key.
  
  Thanks again
  
  gerry
- May 12, 2011 at 4:51 pm #32297
  Jackpine
  Participant
  - Offline
  That's why a loose ground and a bowl of Rice Crispies sound the same….
  
  Snap, Crackle, Pop…..
  
  People are hilarious...
  I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!
- May 12, 2011 at 5:05 pm #32299
  RichWaugh
  Participant
  - Offline
  Hmmmmm…I must have a bad ground in my knees.
- May 12, 2011 at 10:31 pm #32304
  Bob Rooks
  Participant
  - Offline
  Rich wrote:
  
  “Hmmmmm…I must have a bad ground in my knees.”
  
  With me it's electrolysis.
  
  Account deleted.
- May 12, 2011 at 11:09 pm #32306
  RichWaugh
  Participant
  - Offline
  Gee Bob, I had no idea you were so vain as to have electrolysis. Wouldn't bikini wax be quicker?
- May 13, 2011 at 6:55 am #32307
  Bob Rooks
  Participant
  - Offline
  Account deleted.
Author

Posts