284 Roller Pin Problem??? |

This topic has 8 replies, 3 voices, and was last updated 12 years, 4 months ago by WillieByrd67.

Viewing 8 reply threads

Author

Posts
- June 11, 2012 at 7:53 am #30592
  WillieByrd67
  Participant
  - Offline
  Need help guys. I have a 284 that will not shift. It is stuck in reverse. From what I have seen on this site, looks like it may be a broken internal roller pin. Looks like the right fender and the right floor board has to come off to get to the right side access door on the tranny. Any help on this project would be appreciated. Thanks!
- June 11, 2012 at 8:12 am #34728
  Tinbender
  Participant
  - Offline
  Is it a shuttle shift? If so it could be a few different roller pins.
- June 11, 2012 at 8:33 am #34729
  WillieByrd67
  Participant
  - Offline
  It is a shuttle shift. This is on an 06 Jinma, Sorry for the confusion. All movement from the shifter to the tranny seems to be fine. The problem is inside. Never had to go into the tranny before. Just need to know what to look for. Thanks!
- June 11, 2012 at 8:53 am #34732
  Affordable
  Participant
  - Offline
  Most of the time it's the roll pin on the lever coming out of the side of the transmission that causes the problem. If it's not the roll pin you have a bent Shuttle shift fork.We have any part you may need in stock
  
  Tommy
  
  Affordable Tractor Sales
  
  “Your Jinma Parts Superstore”
  
  http://www.affordabletractorsalesco.com
- June 14, 2012 at 10:18 am #34752
  WillieByrd67
  Participant
  - Offline
  Okay, I have the right fender and floor plate off. I need to know if I can go through the right brake or does it need to come off also? Looks like it will need to come off to access the linkage where it goes into the tranny.
- June 15, 2012 at 5:28 am #34756
  Affordable
  Participant
  - Offline
  I'm not sure what you are looking for, once you have the floorboard up you should see where the linkage connects to the side of the shuttle housing, there is a plate there with 6-8 bolts that will remove that has a fork on it, 90% of the time it's a roll pin on the outside did you check that already ? Here is a pic of the SHuttle shift plate
  
  https://affordabletractorsalesco.com/cart/sub_catalog_gallery.php?cid=1692&catid=&picid=3824&category=ZL-20&sub_category=&scid=
  
  Tommy
  
  Affordable Tractor Sales
  
  “Your Jinma Parts Supperstore”
  
  http://www.affordabletractorsalesco.com
- June 15, 2012 at 9:39 am #34758
  WillieByrd67
  Participant
  - Offline
  Tommy, This tractor has a linkage that ends at a lever( like a counter lever), and where it goes into the tranny there is no plate. It is just a welded part to the tranny body from what I can see. The linkage that goes inside the tranny is freely moving with NO resistance at all. What has broken is inside the tranny. Sorry, I haven't figured out how to install a picture on this site. I can send one to your email if you would like.
- June 15, 2012 at 1:58 pm #34761
  Affordable
  Participant
  - Offline
  e-mail the pics to tommy@affordabletractorsalesco.com
- June 15, 2012 at 2:34 pm #34762
  WillieByrd67
  Participant
  - Offline
  Tommy, I think I have been straightened out by Ronald @ Ranch Hand with some pics. I was looking at the back of the tractor around the rear axle where the linkage ends. He has shown me a picture where the plate for the shuttle shift is much further forward. Thanks you guys sooo much for being patient with an IDIOT!
Author

Posts

Viewing 8 reply threads

You must be logged in to reply to this topic.