Forum › Forums › Tractor Modifications › remote fuel filter bowl assembly
- This topic has 13 replies, 5 voices, and was last updated 11 years, 10 months ago by DavidPrivett.
-
AuthorPosts
-
-
December 3, 2012 at 7:48 am #30695
the 2006 ft 504a foton I have uses a remote filter bowl it has no filter screen in tank 1/4 inch pipe thread.the turn off valve is leaking on the filter assm.,I took it apart and I really do not like the valve gasket design.has anyone found a different type bowl filter with shut off valve that can be used.I looked at the old ford and IH designs but they are 3/8 pipe for the inlet.Or should I do away with the filter and just add a good valve,it has a screen in the inlet of the manual pump on the injector and a canister filter I use a napa 3195.
-
December 3, 2012 at 1:23 pm #35372
well I still have a rubber fuel line in between the tank and the bowl that I wanted to get rid of but a ford filter for a 8n worked to the stock brackets just got a flare to barb fitting and cut off the banjo fitting on the outlet of the old fuel line.
-
December 9, 2012 at 7:45 pm #35392
and got rid of that plastic fuel bowl, glass is so much easier to see the condition of the fuel that it contains.and glass does not care (i dont think) about uv rays
-
December 9, 2012 at 11:40 pm #35393
Glass certainly is susceptible to UV rays – in a hundred years or so it will develop a purplish tint if you're not careful.
-
December 9, 2012 at 11:49 pm #35394
It has also been known to sag, deform, and form ripples. After all, it's just sand that's been melted togrther.
Account deleted.
-
December 11, 2012 at 8:07 am #35395
I have dug up old glass and seen the purplish color and I just thought that was the color it was blown or cast in.and the deformation I assume that excess heat causes this?
-
December 11, 2012 at 8:25 am #35396
Actually, glass is just fused silica for the most part and is a plastic medium – that is, it can be deformed by pressure. Very old window panes are seen to be thicker at the bottom than at the top, because the glass has actually “flowed” toward the bottom under the pressure of gravity and lots of time.
In sunlight, clear glass will develop that purplish tint after several decades due to the action of UV o the glass. This is a faint purple – a deeper purple would be a color that was put in the glass at time of production.
-
December 11, 2012 at 12:32 pm #35397
I learned this long ago when I remodeled old homes in Oakland Ca. for free rent. Many of the broken windows I replaced would be 1/16-1/8″ at the top and 1/4″ at the bottom and as wavy as the curtains behind them.
-
December 13, 2012 at 7:07 pm #35413
well I learned something new today I had no idea glass could move.Is there hard and soft glass? does one move easier than the other,or is plate glass all the same?
-
December 13, 2012 at 9:25 pm #35416
That's a good question. Even tempered glass (the kind that shatters) can be bent. When I did bodywork at some shops we would use a piece of glass from a pickup truck rear sliding window to mix bondo on. After a year or so that flat glass would have a bowl in the center 1/4″ deep.
-
December 14, 2012 at 11:17 pm #35424
I remember learning in chemistry class that glass was a supercooled solution. Old church window being thicker on the bottom were always used as an example of how glass flows over time. In fact, glass is an amorphous solid that doesn't flow. Variations in thickness of glass were a result of the manufacturing process. The thicker end would be placed at the bottom for stability. Modern manufacturing processes result in glass with a uniform thickness. Studies using sensitive measuring equipment show no change in thickness over time. If there are any chemists out there please correct me if I'm wrong.
-
December 14, 2012 at 11:40 pm #35426
-
December 15, 2012 at 12:12 am #35428
Hmmm…whoda thunk it?
-
December 17, 2012 at 7:15 am #35431
I guess in hind sight the glass should have been placed thick side up cause in 1100 billion trillion years the glass would have moved down to create a flat pane.I do not think I' ll wait for it to happen.
-
-
AuthorPosts
- You must be logged in to reply to this topic.