Forum › Forums › Tractor Operation And Maintenance › Hydraulics on farm pro 2430
- This topic has 12 replies, 6 voices, and was last updated 10 years, 9 months ago by Affordable.
-
AuthorPosts
-
-
September 26, 2013 at 9:16 pm #30819
I have attempted to rebuild my hydraulic pump. The rebuild was simple enough, however, the tractor will not start. It is like it is locked up. You can't even pull it to start it. What am I missing?
-
September 27, 2013 at 9:23 am #36427
Sounds like the pump maybe dead heading ,loosen the bolts up on the pump the ones that hold the pump together ,see if that helps, if yes it could be your pump body is warped ?kit not installed correctly, ect. There are 2- different pump kits, one is thinner than the other
Also check your quick connects to make sure they are seated correctly
Tommy
Affordable Tractor Sales
“Your Jima Parts Superstore”
-
September 27, 2013 at 3:12 pm #36428
Thanks, will try.
-
September 27, 2013 at 7:47 pm #36429
OK. Here's my latest. Replaced the hydraulic pump. Worked fine for about 15 minutes while grading drive. Then the tractor began to smoke abnormally on deceleration and the FEL stopped working. The power lift worked. I'm at a loss. Any help would be appreciated.
-
October 3, 2013 at 1:13 pm #36435
What color was the smoke, and what do you mean by “smoke abnormally on deceleration.”?
Account deleted.
-
October 5, 2013 at 10:37 pm #36447
Thanks for replying. Situation has been resolved. The seal between the hydraulic pump and the engine failed allowing hydraulic fluid to over fill the crankcase causing the smoking. The hydraulics failed obviously from the loss of fluid. Replaced the seal and changed the oil and added fluids. Everything working normal now.
-
October 7, 2013 at 8:55 am #36452
Most of the time what causes that seal to fail or blow out is a deadhead situation, keep a close eye on it
Tommy
Affordable Tractor Sales
“Your Jinma Parts Superstore”
-
February 5, 2014 at 6:32 pm #36755
Really don't know how to ask questions but my rear hydraulics on a farm pro 25 hp is working very slow. The front bucket seems to be working fine. temp outside is around 25/30. Is there a different hydraulic fuel fill for rear or is their only one fill. Where is that fill so I can make sure I am puttling fluid in the correct place. Thanks
-
February 6, 2014 at 10:04 am #36756
The hydraulic fill is behind the seat for the 3- point lift and the loader, you prob. have a separate Pump and res. for the power steering. What type of Hydraulic oil are you using ? We recommend AW032 Wt. oil, Universal Hydraulic oil is 46 wt I think. SO the thinner oil will work faster in the colder climates
Tommy
Affordable Tractor Sales
“Your Jinma Parts Superstore”
-
February 6, 2014 at 7:47 pm #36757
Thanks, I use regular fluid, I will try the thinner fluid.
Roger
-
February 7, 2014 at 8:10 am #36758
hey tommy, does my jinma 254 have a separate res/pump for the power steering. I was not aware it did
thanks
-
February 7, 2014 at 1:42 pm #36759
dogdoc, some do and some don't. Easy enough to spot though. If you have two pumps you have two pumps, one right in front of the other, and a 1 liter (roughly) reservoir in front of the radiator. Here's a pic…
-
February 7, 2014 at 2:22 pm #36760
That is correct, good Pic Tinbender
Tommy
Affordable Tractor Sales
“Your Jinma Parts Superstore”
-
-
AuthorPosts
- You must be logged in to reply to this topic.