Hello to all it`s Terry t yosemite tractor 306 dozer grinding feal

Forum Forums Bulldozer & Excavator Troubleshooting Hello to all it`s Terry t yosemite tractor 306 dozer grinding feal

Viewing 13 reply threads
  • Author
    Posts
    • #30983
      Yosemitetractor
      Participant
        • Offline

        I just got in a 306 dozer 2007 year with about 200hrs on it. When you put any load on it there`s a grinding sound and a shutter forward movement stops. You use the forward reverse leaver it hooks up for a little bit then back to grinding and shuttering. It was really fun to get it on the trailer to get it here. I have the engine out and the all the hyd clutch out and don`t see any stripped shaves or burned clutch disks. If the hyd pressure was low does the clutch slip smooth or a shutting? Now I`m thinking ring and pinion. What do you guys think?

      • #37439
        Bob Rooks
        Participant
          • Offline

          What was the clutch hydraulic pressure before you disassembled it?

          What does the clutch input shaft spline look like?

          Do you know the operating principles of the hydraulic shuttle clutch? Like what causes it to engage and disengage?

          There is a remote possibility that the issue lies within the bevel gear.

          What type of oil has been used in the bevel gear compartment and in the shuttle clutch?

          Account deleted.

        • #37440
          Yosemitetractor
          Participant
            • Offline

            I didn`t check the hyd pressure before I pulled it a part.

            The input spline look fine no sigh of and distorison.

            The piston gets pushed by hyd pressure in to the clutch pack either forward or backwards and those parts look fine.

            The oil that came out kinda looks like AW46 but the customer has put other kinds of oil in there as he had leaks.

             

            I`m going to mark all the hoses today so I can look in to the rear end and see what I can find back there.

          • #37444
            Bob Rooks
            Participant
              • Offline

              The hydraulic pressure RELEASES the clutch discs and plates, the springs are what ENGAGE the clutch pack. Just like a Cat.

              AW46 is the wrong oil to use in the shuttle clutch, but can get by for a short while. Do not use UTF, ATF, or THF oils. Recommended oil is ISO AW 220 MACHINE OIL, or Caterpillar TO-4. These oils have an AGMA rating of 5.

              The transmission and bevel gear case should be using 75W-90 or 85W-90 gear oil. Anything less and you're asking for trouble. Final drives should have 90W-140 gear oil.

              Account deleted.

            • #37450
              Yosemitetractor
              Participant
                • Offline

                I do see wear on the 6 spline main shaft all ready where it slides in to the adaptor on the flywheel. Any idea if the new parts are a harder shaft?  This dozer only has 200 hres on it.

                 

                Thanks

                Terry

              • #37451
                Bob Rooks
                Participant
                  • Offline

                  Can you post a picture of it please? Don't know if a new shaft would be case hardened or not, but that could be done.

                  Account deleted.

                • #37452
                  Yosemitetractor
                  Participant
                    • Offline

                    Pic

                  • #37453
                    Bob Rooks
                    Participant
                      • Offline

                      It's pretty difficult for first time users to post a pic, but easy as pie once you've done it. Click on the little tree in the formatting bar directly above your text, then click on the image to the right of the “Image URL” text box. Then search your computer for the picture file.

                      Account deleted.

                    • #37454
                      Bob Rooks
                      Participant
                        • Offline

                        If my suggestions don't work, these will:

                        http://www.ctoa.net/category/u…..-our-site/

                        Account deleted.

                      • #37457
                        Yosemitetractor
                        Participant
                          • Offline

                          Still cant post a pic but I did put a pick in the photo album called dozer

                        • #37459
                          Bob Rooks
                          Participant
                            • Offline

                            Sorry, I didn't see it. But even if I did, I couldn't open it anyway. Something is wrong with this site again.

                            Try posting the pic here:

                            https://www.facebook.com/yuchaidozer?ref=bookmarks

                            Account deleted.

                          • #37466
                            Bob Rooks
                            Participant
                              • Offline

                              Hi Terry, did you read my response on the FB page?

                              Account deleted.

                            • #37498
                              Yosemitetractor
                              Participant
                                • Offline

                                Where do I get the splined bushing to fit the drive plate

                                on the flywheel?

                              • #37499
                                Bob Rooks
                                Participant
                                  • Offline

                                  Did you try Circle-G or Yuchai directly? Might be able to have a machine shop make a few.

                                  Do you have a part number?

                                  Not sure what splined bushing you are referring to.

                                  Account deleted.

                              Viewing 13 reply threads
                              • You must be logged in to reply to this topic.