Forum › Forums › Site Questions and Help and Features › BACK HOE NOT WORKING
- This topic has 11 replies, 3 voices, and was last updated 11 years, 3 months ago by Glenn Southworth.
-
AuthorPosts
-
-
July 22, 2013 at 8:50 pm #30795
I have a LW6 backhoe and it stopped working the last time I put it on the tractor. It is pumping fluid but not building pressure. It just seems to just circulate and it causes the fluid to foam. I took the pump apart but it looked ok. I have heard people saying that they cleaned the relief valve? I took the valve out that adjusts the pressure and it looked clean. Any help would be appreciated. thanks, Glenn
-
July 22, 2013 at 9:37 pm #36217
If it is foaming, it sounds like it is sucking in air somewhere. Check the intake side of your pump system thoroughly. Foamy hydraulic fluid is full of air, so it compresses and can't transfer power.
-
July 23, 2013 at 7:07 pm #36220
I don't think its sucking air it wont do anything.Stabilizers wont even go down. I am not sure what valve people are cleaning and where it is. It just seems to be circulating and not building any pressure at all. What holds the pressure in the valvebody of the controls? Thanks for the idea though I will check again.
-
July 24, 2013 at 3:14 am #36221
First let us see if we are talking about the same control valve.
ronj
ronjin
-
July 24, 2013 at 8:56 pm #36222
Yes that's what I was talking about. I took out the valve on the right…looks like its too adjust the pressure . Didn't see any dirt
-
July 24, 2013 at 10:05 pm #36223
When you look at the left portion of the picture, the lower left line is labeled as Hyd In. The portion of the control valve that is just above that and to the left holds the Relief Valve. It has a screw plug with an allen wrench removal slot.
Here is a picture of the relief valve assy.
RonJ
ronjin
-
July 25, 2013 at 5:03 pm #36224
I took one out that looks like that on the right side….but I don't think I got it all I think the “piston” with the o ring is still in there. Maybe that is stuck. Its raining now but I will look at the left again to see if I missed it tomorrow. Thanks for the picture that will be helpful.
-
July 29, 2013 at 9:45 pm #36238
Got it working. Think the valve was stuck. You were right the hoe was off the tractor and i took the back cover off so the valve was on the right. Now that its working the the control valve for the boom is leaking out the botom cup. I figure the seal is gone. Can you buy rebuild kits for those or do you need to buy the whole valve assembly? Im going to take the valve out tomorrow and see what it looks like.
-
July 30, 2013 at 12:20 am #36239
Here is what the spools look like.
RonJ
ronjin
-
July 30, 2013 at 11:45 am #36240
I have oil leaking into the spring area. Im thinking those are seals just above the spring? The orings should be easy to get but the other ones look like squared orings? Do they make kits or where can I get them. Thanks
-
July 30, 2013 at 1:00 pm #36241
In the photo, the others look like cup seals to me, but I could b e wrong. Still, most of these valve parts are kind of standard and a hydraulic shop should have them. If not, you can probably find them at McMaster-Carr or MSC Industrial Supply online. You just need to get accurate measurements fom the old ones and they'll be able to come up with replacement parts. I'd start by checking with the Jinma dealers here, they may have some parts in stock.
-
July 31, 2013 at 8:09 pm #36255
ok. Thanks for the help guys!
-
-
AuthorPosts
- You must be logged in to reply to this topic.