Oil being pushed out of the crankcase ventilator

Forum Forums Tractor Troubleshooting Oil being pushed out of the crankcase ventilator

Viewing 8 reply threads
  • Author
    Posts
    • #30172
      frankg
      Participant
        • Offline

        Started this topic before the site change. Cleaned the screen and tube in the ventilator which wasn't dirty. Used the tractor today and again still having oil being pushed out inside of air going in. Anybody else got a cause or a solution for this?

      • #31312
        SpringValley
        Participant
          • Offline

          I see in your old post that you talked about smoke coming out of the ventilator.  Take the oil cap off with engine warm and at idle.  Do you see a puff, puff, puff of smoke, a steady stream of smoke etc ?  

        • #31325
          Jackpine
          Participant
            • Offline

            Just a thought…. haven't seen the old post. But have you done a compression test on the cylinders? hmmm

            People are hilarious...
            I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!

          • #31336
            frankg
            Participant
              • Offline

              I checked and smoke is also coming out the oil cap when removed and even some around the center nut holding down the valve cover also front edge of the valve cover. Unfortunately I don't have the tools to check the compression.

            • #31337
              frankg
              Participant
                • Offline

                Sorry I forget to include I also see a puff puff not a steady stream of smoke.

              • #31344
                SpringValley
                Participant
                  • Offline

                  That's a very bad sign.  That's blow-by and it means that compression is blowing by the rings.   That's what makes the high crank case pressure and it's what is blowing the oil out the ventilator. 

                  You should really inspect the intake system to see if there is a cracked hose or other problem that let it suck dirt into the engine.

                  From what I can tell long distance you are going to have to at least an in frame overhaul on the engine.   You should really find somebody that can do a compression check to verify.  

                • #31350
                  Jackpine
                  Participant
                    • Offline

                    I concur with Larry. kissass laugh

                    The “puff puff” of smoke and not steady suggests that one (or more) of the cylinders has bad/broken rings. See if someone you know has a compression tester. Or you may find one for a cheap price. Can you say… “harbor freight?”  wink

                    Do the test first to confirm it. If it does indeed show a bad cylinder, then you will have to tear it down and replace the rings. You need to get a good look at the cylinders to make sure it didn't score the cylinder walls. If that's the case, then you'll be in need of a good machine shop or replacement if it's really bad. When you put it back together, replace all the rings and I'd also suggest new rod bearings since you are in there anyways. This keeps you from having to do it again for awhile.  yell

                     

                    Jack

                     

                    People are hilarious...
                    I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!

                  • #31362
                    Bob Rooks
                    Participant
                      • Offline

                      You can make a compression test or leak-down test adapter from an old fuel injector or an old glow plug. You're not likely to find the correct adapter in any kit.

                      If you have compressed air handy you can perform a crude leak-down test with just a rubber tipped air nozzle stuck in the injector hole. Max. 20 psig.

                      Account deleted.

                    • #31402
                      frankg
                      Participant
                        • Offline

                        Thanks guys even though it's only got 105 hours on it you right about changing the bearings anyways. My dealer retired so I'm going to shop around to find a repair shop. Hopefully I believe there are sleeves in the block so it might not be that bad.

                        frown

                    Viewing 8 reply threads
                    • You must be logged in to reply to this topic.