Forum Replies Created
-
Posts
-
I have same dozer mine dont have grease fittings on either end..the manual said there suppose to be but mines not even drilled for it
35xtd Dozer and hoe..1610d yanmar tractor
I bit the bullet and bought one …..tjey dont have a oil sump u mix 50:1 just like any other stihl….cut with it 2hours today plenty torque hard to get usef to the sound…it dont sound like a 2 stroke…everthing i own id s stihl but thid id the first four stroke i havent seen anything yet it wont cut think ill get a blade attatchment for it tommorrow evening
35xtd Dozer and hoe..1610d yanmar tractor
my dozer has the 4l22-ta it runs around
100 degress too i thought that was to low but bob from nortrac says thats what it suppose to run
35xtd Dozer and hoe..1610d yanmar tractor
thanks for ur help..its nice to know somebody that has worked on these little machines before and have a website devoted to these little beasts…is yours a standard tranny or shuttle shift….i wished id looked around and found a shuttle shift..how do you upload videoes and pics on here…i got some videoes of my two boys operating the backhoe they love it
35xtd Dozer and hoe..1610d yanmar tractor
ive tried to get the plugs out i think im gonna have to drill and ez out…..bob from nortrac said the ceramic clutch disks shouldnt slip with oil on them but the brake bands isnt as effective….i wonder if my oil sump is in the middle….next oil change i might take the plate off the oil pan and look….i was wondering if your dozer has grease fittings on the front and rear swing shaft bushings my book says mine does but in reality theres not even a place for a grease fitting….so you came up with a better design for the steering clutches and the brakes i may have to get you to draw me a pic..its a poor design hard to keep them in sequence to get the brake to grab right sometimes the clutch isnt fully disengaged hard to get it right..but with patience it can be done..
35xtd Dozer and hoe..1610d yanmar tractor
you got a nice looking dozer on your profile how long have you had your rob rooks?
ive only had mine about 8 months…had to send it back twice over the right steering clutch…..it slips sometimes but sometimes it dont they never could figure out y…and the fuse box melted..ive got 94hrs on it so far its done more than i thought it could it pushes better than dads td9 and my brothers jd 1010….but the right clutch is aggravating me i dont wanna tear in to it cause its still under warranty but they cant fix it…and the oil pressure..what you said about the dipstick makes alot of sense…i
dads old td9 we have to overfill it to push on a hill….i was hoping i wouldnt have to do that with this one cause when ur in the level it has to be hard on the motor..
35xtd Dozer and hoe..1610d yanmar tractor
you may be right on the dipstick…the book calls for 1.6 gallons…but i have to put 2 gallons in it for it to be right on the dip stick….mines a four cylinder laidong engine…i called nortrac and all they can tell me is what the book says not very helpful..i think the book is for another dozer like a yuachi or guillen they just put a pic of my dozer on the cover
35xtd Dozer and hoe..1610d yanmar tractor
the only thing i can figure is the oil sump is toward the back of the motor because i can climb a tree foward and oil pressure never dips but if i back up a hill if its steep oil pressure will dip
35xtd Dozer and hoe..1610d yanmar tractor
engine oil pressure….so id have to overfill it to keep oil pressure on a incline
35xtd Dozer and hoe..1610d yanmar tractor
