Affordable

Forum Replies Created

Viewing 10 posts - 331 through 340 (of 449 total)
  • Author
    Posts
  • in reply to: New Foton 40 hp problem #33210
    Affordable
    Participant
      • Offline

      Sounds like your main fuse has blown ,check all the fuses

      Tommy

      Affordable Tractor Sales

      “Your Jinma Parts Superstore”

      http://www.affordabletractorsalesco.com

      in reply to: Jinma 284 4×4 stoppped working #33139
      Affordable
      Participant
        • Offline

        Did you get the 4 x 4 shaft down ? Here is what you should have for parts

         

        6- 8mm ball bearings for each end of shaft (12 total)

        2-Rubber dust boots

        1-24mm Circlip

        1-Starwasher

        1- Spring

        1-Washer

        1- Coupler I

        1- Coupler II

        1- Shaft

        1- 4 x 35 pin

         

        You can look on our website under 4 x4 parts 200 series and see these same parts for reference.Most of the time the Circlip will break which will allow the coupler to slide back too far and the 8mm ball bearings fall out.

        You can also send me a e-mail if you have some questions and I will try to help you tommy@affordabletractorsalesco.com

         

        Tommy

        Affordable Tractor Sales

        “Your Jinma Parts Superstore”

        http://www.affordabletractorsalesco.com

        in reply to: Jinma 284 4×4 stoppped working #33140
        Affordable
        Participant
          • Offline

          Did you get the 4 x 4 shaft down ? Here is what you should have for parts

           

          6- 8mm ball bearings for each end of shaft (12 total)

          2-Rubber dust boots

          1-24mm Circlip

          1-Starwasher

          1- Spring

          1-Washer

          1- Coupler I

          1- Coupler II

          1- Shaft

          1- 4 x 35 pin

           

          You can look on our website under 4 x4 parts 200 series and see these same parts for reference.Most of the time the Circlip will break which will allow the coupler to slide back too far and the 8mm ball bearings fall out.

          You can also send me a e-mail if you have some questions and I will try to help you tommy@affordabletractorsalesco.com

           

          Tommy

          Affordable Tractor Sales

          “Your Jinma Parts Superstore”

          http://www.affordabletractorsalesco.com

          in reply to: Jinma 284 4×4 stoppped working #33141
          Affordable
          Participant
            • Offline

            Did you get the 4 x 4 shaft down ? Here is what you should have for parts

             

            6- 8mm ball bearings for each end of shaft (12 total)

            2-Rubber dust boots

            1-24mm Circlip

            1-Starwasher

            1- Spring

            1-Washer

            1- Coupler I

            1- Coupler II

            1- Shaft

            1- 4 x 35 pin

             

            You can look on our website under 4 x4 parts 200 series and see these same parts for reference.Most of the time the Circlip will break which will allow the coupler to slide back too far and the 8mm ball bearings fall out.

            You can also send me a e-mail if you have some questions and I will try to help you tommy@affordabletractorsalesco.com

             

            Tommy

            Affordable Tractor Sales

            “Your Jinma Parts Superstore”

            http://www.affordabletractorsalesco.com

            in reply to: Jinma 284 4×4 stoppped working #33138
            Affordable
            Participant
              • Offline

              Did you get the 4 x 4 shaft down ? Here is what you should have for parts

               

              6- 8mm ball bearings for each end of shaft (12 total)

              2-Rubber dust boots

              1-24mm Circlip

              1-Starwasher

              1- Spring

              1-Washer

              1- Coupler I

              1- Coupler II

              1- Shaft

              1- 4 x 35 pin

               

              You can look on our website under 4 x4 parts 200 series and see these same parts for reference.Most of the time the Circlip will break which will allow the coupler to slide back too far and the 8mm ball bearings fall out.

              You can also send me a e-mail if you have some questions and I will try to help you tommy@affordabletractorsalesco.com

               

              Tommy

              Affordable Tractor Sales

              “Your Jinma Parts Superstore”

              http://www.affordabletractorsalesco.com

              in reply to: Jinma 284 4×4 stoppped working #33136
              Affordable
              Participant
                • Offline

                Did you get the 4 x 4 shaft down ? Here is what you should have for parts

                 

                6- 8mm ball bearings for each end of shaft (12 total)

                2-Rubber dust boots

                1-24mm Circlip

                1-Starwasher

                1- Spring

                1-Washer

                1- Coupler I

                1- Coupler II

                1- Shaft

                1- 4 x 35 pin

                 

                You can look on our website under 4 x4 parts 200 series and see these same parts for reference.Most of the time the Circlip will break which will allow the coupler to slide back too far and the 8mm ball bearings fall out.

                You can also send me a e-mail if you have some questions and I will try to help you tommy@affordabletractorsalesco.com

                 

                Tommy

                Affordable Tractor Sales

                “Your Jinma Parts Superstore”

                http://www.affordabletractorsalesco.com

                in reply to: Jinma 284 4×4 stoppped working #33137
                Affordable
                Participant
                  • Offline

                  Did you get the 4 x 4 shaft down ? Here is what you should have for parts

                   

                  6- 8mm ball bearings for each end of shaft (12 total)

                  2-Rubber dust boots

                  1-24mm Circlip

                  1-Starwasher

                  1- Spring

                  1-Washer

                  1- Coupler I

                  1- Coupler II

                  1- Shaft

                  1- 4 x 35 pin

                   

                  You can look on our website under 4 x4 parts 200 series and see these same parts for reference.Most of the time the Circlip will break which will allow the coupler to slide back too far and the 8mm ball bearings fall out.

                  You can also send me a e-mail if you have some questions and I will try to help you tommy@affordabletractorsalesco.com

                   

                  Tommy

                  Affordable Tractor Sales

                  “Your Jinma Parts Superstore”

                  http://www.affordabletractorsalesco.com

                  in reply to: Jinma 284 4×4 stoppped working #33134
                  Affordable
                  Participant
                    • Offline

                    The weather in Texas is 109 degrees, our guys are only wearing Boxers now,all the other clothes are being used for packing (LOL)

                    Just kidding the local thrift store gives us the cotton clothes for shop rags by the bag full, so we started packing with them.We now have customers that ask about certian size T-Shirts, ect. Its very funny.

                    Tommy

                    Affordable Tractor Sales

                    “Your Jinma Parts Superstore”

                    http://www.affordabletractorsalesco.com

                    in reply to: Nortrac 204c trouble shifting into gear #33125
                    Affordable
                    Participant
                      • Offline

                      Thats what it's all about,helping each other out.

                       

                      Thanks for the order we appreciate the business

                       

                      Tommy

                      Affordable Tractor Sales Co

                      “Your Jinma Parts Superstore”

                      http://www.affordabletractorsalesco.com

                      in reply to: Task master dealer? How hard to replace clutch on 432d #33115
                      Affordable
                      Participant
                        • Offline

                        Try Yosemite Tractor see if he knows somebody in Southern ,Ca.

                        http://www.yosemitetractor.com/

                        Tommy

                        Affordable Tractor Sales

                        “Your Jinma Parts Superstore”

                        http://www.affordabletractorsalesco.com

                      Viewing 10 posts - 331 through 340 (of 449 total)