Forum Replies Created
-
Posts
-
I have it attached,but i didn't start the pto yet.
Guess i.ll have to go with the chain and bar
Should have known better,after reading the post over and over
Give me your way of doing this,when you get time!!
Thanks everyone for your patients!
Here it is..a bit rough,but seems like a very solid install..maybe i'll add a chain just in case!!
PTO gearbox filled with 80W90 gear oil..ok i hope………..
BH tank took 5 gal ISO AW32 so far…
Thanks Again
Ben……..
Everybody must be in church!
God Bless You All………..
Thanks Rich,
I'm beginning to see the pitcher,should be able to test it tomorrow!
Please someone tell me what kind of oil to put in the RED gearbox that goes on the PTO attached to the PTO pump..it's dry so i need to put something in there before i start it up…..Have no manual on the gearbox or pump…
Enjoy the sunshine….whatever that looks like!
Thanks Everyone
Cheers
Ben…………
After a lot of trial and error I finally got the pump attached ,it's not a professional job,but best i could do with the little knowledge and tools i have.
Here's a few pics…please be kind ..lol
My wife just got back from church,she must have been on her knees praying for me,while i was on my knees swearing on that PTO thing! God Love Her!
Bob,gotta do something with it today,i have 4 steel brackets made up to go from the gearbox (the red part) to the 4 hole where the weather hood came off,hood won't fit now with the pump there..I think this will work ok!
My son picked up the center top link for 3 pt. hitch,but it was to big,so i'm hoping to have the right one delivered tomorrow..
Question i asked before,don't think i got answer: Is the 3 pt. hitch the only thing holding the BH???? My first tractor with BH….
The plug on top of PTO pump gear box Is that where you prime the pump?????
It's so foggy and cold here you wouldn,t be able to find your way anyway!!
Thanks everyone for all the advice!
Ben……………
Good,something i can do..i'm just going to block it for now and use a chain to keep it steady…temporary fix,so i can pump fluid to the hoses ..make sure there's no leaks etc.
Tank full..THE PUMP..to prime just pour fluid where the hose connects?There's a plug on top the RED gearbox it's dry do i put the same fluid in there??..guess i should stick with woodworking……
Wish there was a good manual with this BH..No mention of the pump..
I won't be using it for work or anything.until i get the pump secured.
Have to wait”til Monday to get some brackets made up..
If anyone has any pictures of the way you did it,love to see 'em
Bob Rooks – where are you? Out in the shed!! lol
Near St. Johns,Newfoundland
Thought you meant me……….lol
Wish someone could drop over and set this up for me…
Thanks Much…………..
Ben……….
That sounds like a better way to do it. I'll have another look at it.Something like pic in Berts post…..
OK,you bolt it to gearbox,do you also bolt to draw bar frame,guess so, to keep it from slipping of PTO.
Thanks Again Rich.
Ben…………..
everything…..
Thanks for reply Ron and Bert.I don't know where all the pictures are going that i uploaded ….try it one more time.
Seems like i can only get them in Photo Album,the first 6 or 7 are mine!
OK,finally got the pics ….
What i was trying to do,bolt piece of metal on to red part of pump where spline goes in…slide over PTO drive..then bolt on with the 4 bolts that came from the cover that i removed…I don't have the 4 holes drilled in the metal yet that will bolt into where the hood was removed.
Do you think with a heavier metal,this would work,if so i'd get the welding shop to make up a plate for it?or maybe do something like Bert got there…….
Ron said: Your pump mounts to a reddish colored adapter that then slides over the PTO shaft. Correct? Yes …
I'll check it out in the morning and see what can be done with it!
Hope you can make some sense of what i'm trying to explain……..
Good Night and Thanks!
Ben
Ron,no,no..not the same………
My pump fits over the PTO,but i'm trying to attach it to something to keep it in place..
I couldn't get pic. here so there posted in Photo Album…also pics of the rear of my Kioti tractor..
Model# on pump–CBN-3
Thanks
Ben……
No way to bolt pump up to PTO the way it is ,so to keep it in place i removed the hood that was there and cut out a piece of metal,bolted it to the pump,have to drill 4 more holes and bolt it to where the hood(cover) was.. so it will keep in place …very rough fix indeed!
Looking at my tractor from the rear,it's not the same as yours and the pump looks different …………I have a LK3054xs Kioti and a LW6 china BH.
Sorry if i'm not making myself clear…..it's all new to me..
Appreciate you trying to help,if there's anything else you can think of
let me know…………
There's no PTO shaft with the BH.
Posted a few pics ..
Thanks Again
Pics. didn't show………….I'll try again!!!!!!!!!!!!
Ben……
