Forum Replies Created
-
Posts
-
Sounds to me like it's time to…. CUE THE DUCK! AFLAC!
Seriously though Hal. Hope this all works out for ya.
Insurance companies are quick to take your money. Just a invoice and a check involved. But when it comes to paying out, there is more paperwork, red tape, and BS involved, it seems like they are debating the national budget.
By the way Hal….. exactly what is the definition of “limited destruction”?
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!LMAO Larry!
In that case, no repairs are needed. 
Then we would just have to park it on the shoulder of 41 and the parade would last only 10 minutes. That's about the time it takes for people to walk slowly from one end to the other. It actually takes me longer to drive into the Post Office from my place.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!Well you are a good father.
You 'load tested” it to insured it would safely hold your daughter. NOT! I'm thinking you are more like the rest of us…. just couldn't resist climbing up there.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!Hope you figure this one out Larry. Seems like a lot of trouble for a “Parade Truck” in Newport since the parade route couldn't even be a mile long.
Let's see…. start at the Safeway….. down to the MW bank on the corner….. down the street past the Pizza Place…. around the corner to the Pub…. around the corner past Napa…. back to the Safeway…. about 1/2 hour at 5 MPH I'd say.
Government is always agreeable.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!Those things look to me like a great way to kill old joints.
Or old idiots
Why didn't you use your new fangled forks to move this Eric?
How many times did you run over the ring before you got the rope “just right”
Nice job. Looks like it should last a couple years at least.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!For what it's worth Keno Tractors has a cross reference chart. The problem with changing oil filters from the manufacturer one is that you have to make sure the size of the filter (So it fits in the space), thread (metric or SAE), and filter media (micron and type)meets the specs.
That being said, here's a link:
http://www.kenotractors.com/fi…..0Parts.pdf
If you don't see your engine type, you should give one of our vendors a call to talk to them. Both Tommy (Affordable) and Eric (Keno) can give you more info.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!HEY ERIC…..
I wasn't ignoring you. Just waiting to hear something back. The welder/plasma set is made in China. It is made “to Northern Tool specs”.
They are a pretty reputable company and it didn't seem to be as cheap looking as some of the others that I came across. They carry the repair parts on hand at Northern Tool. There is a 3 year warranty. It appears to be a “fair” setup for those doing hobby work. HOWEVER.. after my research, I'm going with a Millermatic 180. Sweeeet.
I found one new for $790. I thought about a little bigger one but I don't do that much heavy work. Besides, I have a stick to do that. After telling the wife I was “needing” a welder, she asked me why I needed it. I told her… because. That was the beginning of a discussion. Anyways, I'm still thinking about getting the cutter. It is easier than fighting with the Oxy, right?
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!Wow….
That kind of makes you wonder what the the rest of the welds look like
Hey TB…. here's a link to a Welder, Cutter, Cart, and Helmet set at Northern. Been thinking this would be nice to have. Have to replace an older welder. Or maybe I just think I have to. It's probably Chinese made. That means it should work on Chinese welds, right?
Came across this while researching.
http://www.northerntool.com/sh….._200467213
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!Larry,
Yes I'd be interested. I'm also concerned about bending the FEL bucket. Send me a PM or even post pics here. Who knows? If I don't get them, somebody else might want them.
Also curious about the quick disconnect setup you got. What's the $$$ on something like that? Being right down the road I'm thinking you have it setup for bucket, forks, and snowblower.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!Great question Eric.
I've been thinking I need to get some for moving bunches of baby trees I cut down. Grapples are kind of spendy and bulky.
Also… Kind of wondering about the ones that come complete with backrest that can be hooked up in place of FEL on Jinma 284. I've seen some, but don't whether it will take more work to adapt them than I want to get involved with. Need more info.
Jack
People are hilarious...
I'm supposed to choose and be in one of the 2 parties. And NEITHER is worth a damn!
