Ronald Paulson Ronald Paulson

Forum Replies Created

Viewing 9 posts - 11 through 19 (of 19 total)
  • Author
    Posts
  • in reply to: clutch not working properly #36975
    Ronald Paulson Ronald Paulson
    Participant
      • Offline

      As best I can tell my dozer is 2002. But the engine tag says its 2005 us space approved.

      I removed the hy trans fluid I had in the clutch system. And replaced it with shell rotella hd 30 weight hydro-trans fluid. It was the closest to your thoughts for clutch fluid.

      I ran dozer for 20 minutes in low, first gear and pushed dirt. It did improve it performance but still has has trouble finding neutral as well as engine bogging in both forward and reverse. But it does it less often than before.

      Also my clutch case after running as said above was 180-200 degrees. Is that a normal temp?

      I could not install a pressure gauge as of yet. Due to (wrong fittings) plumbing always seams to take a few try’s.

      Side note the out side of my clutch case after running as said above was 180-200 degrees. Would that be normal?

      in reply to: clutch not working properly #36962
      Ronald Paulson Ronald Paulson
      Participant
        • Offline

        Thanks for the shop tip. Also I’m having trouble finding an oil that has the same ratings as you said above. I can get some types of rotella do you know what would be a similar match in that brand?

        in reply to: clutch not working properly #36960
        Ronald Paulson Ronald Paulson
        Participant
          • Offline

          Yep I pulled it out when I drained original oil and put in the hy- trans. I was hoping that it was plugged but it was clean. I have my fingers crossed that it will help with a better weight of oil. As well with pressure gauges to see what my pump and clutch are doing. This web site is a great tool.

          in reply to: clutch not working properly #36958
          Ronald Paulson Ronald Paulson
          Participant
            • Offline

            Thanks I will try that type of oil.

            in reply to: clutch not working properly #36956
            Ronald Paulson Ronald Paulson
            Participant
              • Offline

              Hi there
              yes on the manual and I also have a parts catalog.

              I will also see if i can put some gages in line and see what pressure i have.

              Ill do some home work on oil in the meantime. To see what’s available in my area.

              Thanks

              in reply to: clutch not working properly #36951
              Ronald Paulson Ronald Paulson
              Participant
                • Offline

                Hi there
                I picked up a used yct306s-6 dozer I have had the machine about five months. It had around 100 hours on it. I have put on about 20 hrs. Im having trouble with my shuttle clutch. Its not finding neutral and when in forward or reverse it lugs the engine almost to a stall. I have drained and changed all fluids motor, clutch, trans. I’m using hy-trans oil in the clutch.
                Any thoughts?
                Thanks

                in reply to: Shuttle Shift noise #36950
                Ronald Paulson Ronald Paulson
                Participant
                  • Offline

                  Thanks bob
                  I started a topic under then heading of clutch not working properly.

                  in reply to: Shuttle Shift noise #36948
                  Ronald Paulson Ronald Paulson
                  Participant
                    • Offline

                    Hi bob.
                    I was wondering how to start a new thread? Or did you mean a whole new topic.

                    in reply to: Shuttle Shift noise #36946
                    Ronald Paulson Ronald Paulson
                    Participant
                      • Offline

                      Hi there
                      I picked up a used yct306s-6 dozer I have had the machine about five months. It had around 100 hours on it. I have put on about 20 hrs. Im having trouble with my shuttle clutch. Its not finding neutral and when in forward or reverse it lugs the engine almost to a stall. I have drained and changed all fluids motor, clutch, trans. I’m using hy-trans oil in the clutch.
                      Any thoughts?
                      Thanks

                    Viewing 9 posts - 11 through 19 (of 19 total)